Most doll problems are visible in the first ten minutes of careful inspection. The problem is that inspection happens either at the factory – where volume pressure wins – or at the buyer, who has no comparison point.
Our process moves the inspection to a fixed checklist between those two points.
Every doll passes ten checks before dispatch: material batch verification, mould seam inspection, channel smoothness, skeleton flex through full range, surface inspection for bubbles and thin patches, colour consistency, weight verification, dimension verification, cleaning, and packaging integrity. A doll that fails is reworked or replaced – it does not ship.
1. Material and batch
Every unit is logged against its material batch. This matters for two reasons: silicone and TPE behave differently from batch to batch, and if a fault recurs we can trace it to a specific production run rather than inspecting blindly.
2. Mould seams
We run a finger along every mould line – thighs, neck, underarms, channel entrances. A seam that can be felt as a ridge will become a tear point within months, because friction concentrates there.
Correctable seams are sanded and re-finished. Seams that are deep, or that cross a joint, fail the unit.
3. Channel inspection
Each channel is checked in both directions with a gloved finger:
- smoothness throughout the full depth;
- no grit, release agent residue or sharp mould flash;
- no thin patches visible under light;
- entrance rim intact with no pinches.
This single check prevents the most common early failure: a tear at the entrance caused by a rough edge.
What fails a unit
| Check | Fails when | Action |
|---|---|---|
| Channel smoothness | Ridge, grit or sharp flash | Rework or replace |
| Channel depth | Below listing spec | Remove from order |
| Entrance rim | Pinched or thin | Replace |
| Skeleton flex | Clicks, grinding or hard stop | Replace |
| Surface bubbles | Any open bubble on a high-wear area | Rework or replace |
| Weight | More than 5 percent under spec | Weigh and re-verify listing |
4. Skeleton flex test
On articulated models, every joint is moved through its full range once. Three things fail a unit:
- Grinding or clicking – internal joint damage.
- Hard stops short of the stated range – manufacturing misalignment.
- Skin pulling at a joint – the material is too thin over the mechanism.
Stiffness alone is not a failure. New joints are stiff and loosen with use.
Articulated torsos and their handling class
GXG2020 Realistic Silicone Half-Body Doll 20.2kg – Lifelike Torso with Inner SkeletonArticulated – full flex test Original price was: $2,250.00.$1,500.00Current price is: $1,500.00.View →
GXG2110 Realistic Silicone Half-Body Doll 21.1kg – Lifelike Torso with Inner SkeletonArticulated – full flex test Original price was: $2,347.50.$1,565.00Current price is: $1,565.00.View →
GXG2800 Realistic Silicone Half-Body Doll 28.0kg – Lifelike Torso with Inner SkeletonHeaviest half-body – extra handling check Original price was: $3,120.00.$2,080.00Current price is: $2,080.00.View →
5. Surface inspection
Under a raking light, the inspector looks for:
- open bubbles in the skin;
- translucent thin patches, especially over breasts and hips;
- colour inconsistency across a single unit;
- release-agent residue, visible as a gloss that does not match the rest.
6. Weight and dimensions
Every unit is weighed and measured. Weight matters because it is the specification buyers rely on most and the hardest to verify from a listing.
If a unit is materially lighter than the listing states, that is a signal of a core or material problem, not a bonus.
Verified weights across the silicone range
GXG765 Realistic Silicone Half-Body Doll 7.7kg – Lifelike Torso with Inner SkeletonListed 7.7 kg Original price was: $855.00.$570.00Current price is: $570.00.View →
GXG1490 Realistic Silicone Half-Body Doll 14.9kg – Lifelike Torso with Inner SkeletonListed 14.9 kg Original price was: $1,657.50.$1,105.00Current price is: $1,105.00.View →- GXG2020 Realistic Silicone Half-Body Doll 20.2kg – Lifelike Torso with Inner SkeletonListed 20.2 kg Original price was: $2,250.00.$1,500.00Current price is: $1,500.00.View →
- GXG2800 Realistic Silicone Half-Body Doll 28.0kg – Lifelike Torso with Inner SkeletonListed 28.0 kg Original price was: $3,120.00.$2,080.00Current price is: $2,080.00.View →
7. Cleaning and dusting
Before packing, each unit is wiped, channels flushed and dried, and the exterior dusted with renewing powder where the material requires it. A doll that arrives clean can be used after a single rinse.
8. Packaging
Plain outer box, no branding, no product names on the label. Inside: foam support at the joints, the unit flat or lightly supported, and a care card.
The sender name on the shipping label is neutral. Shipping documents describe contents generically.
Why each stage exists
| Stage | What it prevents | If skipped |
|---|---|---|
| Mould seam check | Tears at ridge lines | Early channel failure |
| Channel inspection | Entrance tears | Returns within 60 days |
| Skeleton flex | Joint failure under load | Doll that cannot hold a pose |
| Weight check | Under-spec cores | Buyer cannot trust any spec |
| Dry before packing | Mould and odour in transit | Unusable on arrival |
Where faults actually come from
Almost every fault we see traces to one of three sources:
- Mould flash at the channel entrance – the most common, and entirely preventable.
- Thin material over a joint – a moulding issue that only shows under flex.
- Moisture packed in – a simple process failure that ruins an otherwise perfect unit.
All three are catchable before dispatch. That is the entire argument for inspecting at this stage rather than at the factory or at the buyer.
Frequently asked questions
What do you check on each doll before shipping?
Ten checks: material batch, mould seams, channel smoothness, skeleton flex through full range, surface bubbles and thin patches, colour consistency, weight against spec, dimensions against the listing, cleaning, and packaging integrity.
Can I request photos of my doll before it ships?
Yes. Every order is opened and inspected regardless, so we can photograph the actual unit before dispatch on request. Ask our team after ordering with your order number.
What happens if a doll fails inspection?
It does not ship. It is reworked if the fault is cosmetic and correctable, or replaced from the next batch. We do not ship a failing unit with a discount as compensation.
HTM2120 Realistic Silicone Half-Body Doll 21.2kg – Lifelike Torso with Inner Skeleton Original price was: €3,360.77.€2,240.52Current price is: €2,240.52.GXG2800 Realistic Silicone Half-Body Doll 28.0kg – Lifelike Torso with Inner Skeleton Original price was: €2,779.49.€1,852.99Current price is: €1,852.99.GXG2110 Realistic Silicone Half-Body Doll 21.1kg – Lifelike Torso with Inner Skeleton Original price was: €2,091.30.€1,394.20Current price is: €1,394.20.